Production of inlet and outlet ceramic bushings

Luoyang Chengchuang Wear resistant Materials Co., Ltd. recently produced a batch of incoming and outgoing ceramic bushings. The incoming and outgoing ceramic bushings have significant advantages over traditional steel.

The composite split type inlet and outlet bushing is based on a steel shell, and a steel + rubber + ceramic composite lining plate is installed on the inner wall of the steel shell.

The bushing is integrally interchangeable with the original cast metal bushing.

The inner lining plate of the bushing is divided into equal parts. Can be removed or replaced individually.

The discharging and discharging bushing lining plates can be removed or replaced from inside the shell. The guide groove part of the discharging bushing (semi-autogenous mill or grid type mill) can be removed or replaced from inside the mill. The replaced parts can be removed from the grinding mill. Take out the discharge end of the machine.

The discharging bushing lining plate and the guide groove part of the discharging bushing (semi-autogenous mill or grid type mill) are fixed on the metal shell of the discharging bushing with bolts, and the thread surface of the bolts is coated with appropriate anti- The anti-rust coating is loosened, and a special protective cap is attached to the top after fixation to prevent the inflow of slurry.

 Advantages

 1) Significantly reduce the maintenance workload. After a complete replacement, there is no need to dismantle the inlet and outlet bushing shell again during normal maintenance. Only the inner wall lining and other easily worn parts need to be replaced, which can greatly reduce operating time and workload.

 2) The strong bonding between ceramics and rubber makes the liner both impact-resistant and wear-resistant.

 3) Significantly reduce the cost of later purchased materials. The cost of later replacement of all wearing parts of the inlet and outlet bushings usually does not exceed 60% of the overall cost.

 4) Light weight, conducive to energy saving. After modification, the overall weight of the inlet and outlet bushing is significantly...30~50% compared with the original metal parts (cast bushing).

 5) Low noise, the use of polymer materials is helpful to reduce the operating noise of the mill.

 6) The application of high wear-resistant ceramics greatly increases the service life to more than 2 times that of cast bushings.

Luoyang Chengchuang Wear resistant Materials Co., Ltd. recently produced a batch of incoming and outgoing ceramic bushings. The incoming and outgoing ceramic bushings have significant advantages over traditional steel.

The composite split type inlet and outlet bushing is based on a steel shell, and a steel + rubber + ceramic composite lining plate is installed on the inner wall of the steel shell.

The bushing is integrally interchangeable with the original cast metal bushing.

The inner lining plate of the bushing is divided into equal parts. Can be removed or replaced individually.

The discharging and discharging bushing lining plates can be removed or replaced from inside the shell. The guide groove part of the discharging bushing (semi-autogenous mill or grid type mill) can be removed or replaced from inside the mill. The replaced parts can be removed from the grinding mill. Take out the discharge end of the machine.

The discharging bushing lining plate and the guide groove part of the discharging bushing (semi-autogenous mill or grid type mill) are fixed on the metal shell of the discharging bushing with bolts, and the thread surface of the bolts is coated with appropriate anti- The anti-rust coating is loosened, and a special protective cap is attached to the top after fixation to prevent the inflow of slurry.

 Advantages

 1) Significantly reduce the maintenance workload. After a complete replacement, there is no need to dismantle the inlet and outlet bushing shell again during normal maintenance. Only the inner wall lining and other easily worn parts need to be replaced, which can greatly reduce operating time and workload.

 2) The strong bonding between ceramics and rubber makes the liner both impact-resistant and wear-resistant.

 3) Significantly reduce the cost of later purchased materials. The cost of later replacement of all wearing parts of the inlet and outlet bushings usually does not exceed 60% of the overall cost.

 4) Light weight, conducive to energy saving. After modification, the overall weight of the inlet and outlet bushing is significantly...30~50% compared with the original metal parts (cast bushing).

 5) Low noise, the use of polymer materials is helpful to reduce the operating noise of the mill.

 6) The application of high wear-resistant ceramics greatly increases the service life to more than 2 times that of cast bushings.